MPS-3033XP Series

Tri-channel programmable DC power supply


◆ Three channels show and adjust current and voltage at the same time 

◆ Intelligent temperature controlled fun to reduce the noise
◆ Serial/Parallel/Track mode
◆ With SENSE function
◆ 40 groups of storage

Precision Impedance Analyzer


Signal source frequency range: DC, 10Hz~5/10/20/30MHz

 Basic impedance measuring acuracy: ±0.05%

◆ Source position: variable voltage 10mV~2V/Variable current 200uA~20mA

◆Output impedance 25Ω/100Ω, switchable

◆ CC,CV,CR,CP,short circuit,dunamic and other working modes
◆ OVP,OCP,OPP,OHP,multiple protection functions
◆ Accuracy of 0.1%
◆Automatic test function setting
◆ RS-232 interface

PEL-8000 Series

Electronic load

◆Voltage 1mV, Current 0.1mA resolution

◆9 groups storage function

◆Linear power supply, low ripple and noise

◆Over limit alarming function

◆ RS-232 interface

MPS-3600H Series

High precision DC Power supply

USB Oscilloscope/Data logger

  • Hand-held portable, 153(L) x 93(W) x 30(H) mm
  • 1G/250M Maximum sampling rate, 100Mbandwidth,2 channels.
  • 8 Bit ~ 13 Bit vertical resolution.
  • Open source hardware interface to support expansion modules.
  • USB 2.0 interface, USB powered.Comes with PWM output.
  • 72 hours long time data logger.
  • Waveform recording and playback review.
  • Support waveform image import as the comparison reference forreal-time waveform.
  • Support Serial bus decoding (RS-232,RS-485/422, I²C, CAN,SPI,Lin).
  • Supports a variety of current clamps and other physicalvolume custom probes.
  • Support buffer waveform preview and mouse wheel operations.
  • Historical change trend statistics and analysis functions.
  • Pass / Fail detection.
  • Support spectrum analysis and frequency response curvemapping.
  • Support FIR Digital Filtering function.
  • Support UI characteristic curve mapping.



l  Connector type : 2 channels with BNC sockets, 20 mm spacing.
l  Vertical resolution: 8 Bit ~ 13 Bit .
l  Maximum sampling rate (S/s): 250M (real time), 1G (equivalent)
l  Bandwidth ( −3 dB): 100MHz
l  Input coupling: AC/DC.
l  Input characteristics: 1MΩ || 25pF.
l  PC OS requirements: Windows XP, Win 7, Win 8.1, Win10 (32 bit and 64 bit).
l  Over-voltage protection: ±60.0v (x1), ±600.0v (x10). (DC + AC peak)
l  Triggering type: Rising/falling edge according to trigger level, Pulse width trigger.
l  Triggering mode: None, auto, normal, single.
l  Pre-trigger capture: 1%~99%of capture size.
l  Automatic measurements:  Maximum, minimum, average, RMS, frequency, period, positive pulse width, negative pulse width, duty cycle, rise time, peak-to-peak value.
l  Frequency response mapping Scanning the frequency, record the process frequency and magnification data, and draw the frequency response curve.
l  Measurement statistical curve: The historical trend of the automatically measured quantities can be plotted for statistics and analysis.
l  Pass / Fail detection: You can set the upper and lower limits of the measurement quantity, and perform Pass / Fail detection and fault alarm function on the measured signal.
l  Deep measurement: With this function, the waveform jump points are automatically numbered and marked, and the time difference between the two adjacent numbers is automatically displayed.
l  Samples Interpolation: Linear or sin(x)/x.
l  FFT: 1024 ~ 16K points.
l  FFT window function: Rectangle, Hanning, Hamming, Blackman.
l  Math: A+B, A-B, AxB, X-Y,Invert.
l  FIR Digital Filtering: Low-pass,High-pass,Band pass,Band stop filter.
l  Acquisition Modes: Normal mode / High Resolution mode / Peak detect mode.
l  Waveform recording File format : 
and playback: Record depth:
  File size:
l  Save as file: txt, csv, excel,  oscxxx, jpg.
l  Comparison reference Support waveform image import and real-time waveform comparison reference. It can import waveform pictures, set gray level and transparency, move up and down, and zoom in and out horizontally and longitudinally.
l  Data logger Sampling Interval: 1 second to 1 hour.
l  Data logger Record Duration: 1 minute ~ 72 hours.
l  Temperature range: Operating: 0 °C to 40 °C (20 °C to 30 °C for stated accuracy). Storage: −20 °C to +60 °C.
l  Reference Output: 1K Hz, 1.5 V square wave output with 50% duty cycle. Software-configurable PWM output with adjustable frequency and duty cycle.
l  Size: 153(L) x 93(W) x 23(H) mm.
l  Languages (full support): English, Chinese (simplified).
l  Compliance: CE, FCC.
l  Net weight: 210 g.
l  Input sensitivity (10 vertical divisions): 20 mV/div to 2 V/div.
l  Input ranges( probe x1): ±100 mV to ±8 V full scale, in 7 ranges.
l  Input ranges( probe x10): ±1V to ±80 V full scale, in 7 ranges.
l  Timebase selection (10 horizontal divisions): 5 ns/div ~ 60 s/div, in 32 ranges.
l  Typical noise (peak to peak voltage): 20 mV/div 2 mV
50 mV/div 5.8 mV
100 mV/div 8 mV
200 mV/div 22 mV
500 mV/div 38.8 mV
1 V/div 88.2 mV
l  Memory depth  (byte /Ch): 64K 50 ms/div
258K 200 ms/div
645K 500 ms/div
2M 1 s/div
8M 2 s/div
10M 10 s/div
20M 20 s/div
30M 30 s/div
40M 40 s/div
50M 50 s/div
60M 60 s/div
l  PC buffer: Up to 500 frames of PC online data waveform buffer.
l  Trigger type: Hardware
l  Trigger source: Channel A
l  Power consumption: 5 v || (248~279) mA
l  Protocols decoding: UART/RS-232/485/422, I²C,CAN,SPI,lin
l  FIR Filtering: Band-pass, Band-stop
l  Custom probes Support two-point calibration of any current clamp on the market.
MATRIX TECHNOLOGY INC.    Oscilloscope    USB Oscilloscope/Data logger